| Book |
Page |
Context |
 |
 |
1955 2nd Serie s I 959 TRUCK MODEL IDENTIFICATION The truck models for these years included seven different series Serial number interpretation is as follows EXAMPLE l f f 105391 Series Year Assy Unit ...
Plant Number Model 7200 Flint 5391 Unit 112 5 8 W B Built at Flint NOTE 1955 2nd Series 4000 trucks are designated as 4A 4B or 4C models in this catalog only 1955 ...
Series 5000 trucks are designated as 5A 5B or 5C models in this catalog only 1955 2nd Series 6000 trucks are designated as 6A 6B 6C 6D or 6E models in this catalog only 1955 |
|
 |
level gauge tube assy to provide clearance with engine mounting boss INOTE When using on 1955 and 1956 models it will be necessary to use 3799644 Hydraulic Tappets 3794060 Oil Pan and 3722959 Oil Level ...
TNOTE Required when installing 1956 V 8 partial engines and fitted block in 1955 Truck models having FIVE QUART OIL PAN NOTE Remove pilot bearing from crankshaft before installing on Powermatic NOTE When using ...
Lockwasher used to attach exhaust manifold and oil level gauge I ube Assy TTNOTE 1955 model initial installation requires conversion kit 3765004 as shown ANOTE Cvl head gasket 3814003 must be used with this block |
|
 |
NOTE Must be used with 1956 Front Fender Extensions Cannot be used with 1955 Extensions due to difference in roll at wheel opening See group 8 153 TNOTE When using on 1955 56 Models also |
|
 |
1955 ...
also be used on 1955 56 2 Ton jobs for heavy duty usage 58 ALL 348 e 3747312 3741954 3741955 3741956 NOTE With stellite seat and sodium fluid |
|
 |
steering linkage 3732309 1 6 870 NOTE Required on some 1955 models having double taper assembly detail Consists of 1 strg and 3rd arm 1 pitman arm and 1 rod assy 6 104 BOLT |
|
 |
NOTE 838539 Seat must be used on jobs w 0 hydraulic valve lifters TNOTE On 1953 thru 1955 models with Bourdon tube type heat indicator gauge it is also necessary to use Adapter Bushing |
|
 |
TNOTE Gasket 3703488 must be used with 3709945 Also when using on 1955 Truck models cut bolts flush with bottom of flange 60 62 Ser 40 thru 60 6 cyl 2 cam hole |
|
 |
Equip P S TILT stamped T hub 7 dia 3714444 1 1250 NOTE When used on 1955 jobs 3723794 spacer must be used to accommodate oil slinger NOTE Bolts in this assy |
|
 |
TNOTE On early 1955 2nd Ser having double taper assembly detail appropriate 3rd Arm 6 103 and Pitman Arm 6 859 must also be installed |
|
 |
TNOTE Required when any 1959 6 cyl block or short motor is installed in 1955 58 models Reduces full pressure oiling to restricted flow Also requires PLUG 3764579 in group 1 531 at right hand |
|
 |
equipped with in by pass system it is necessary to install reducer bushing 144042 NOTE 4 On 1955 56 models it is necessary to install reducer bushing 3838094 NOTE 5 When using |
|
 |
INSTRUMENT PANEL in prime 55 59 FFC 3727935 1 27 15 NOTE When used on 1955 Models it will be necessary to use 1956 Light Switch because of difference in hole size |
|
 |
panel 3737742 1 7 55 NOTE To be used only when 1957 front fenders are used on 1955 56 models shown I6 603 PANEL EXTENSION PLATE Front Door Sill |
|
 |
Upper Guide 55 64 ALL exc TILT 15 long 3761219 2 35 NOTE Rework as required on 1955 59 models 64 Ser 50 65 66 Ser 50 exc TILT RAIL side door |
|
 |
NOTE Required when any 1959 6 cyl block or short motor is installed in 1955 58 models Reduces full pressure oiling to restricted flow Also requires BOLT 3764578 in group 0 293 at right hand |